Current position > Contact Us
Quick Answer: A multivariable vortex flow meter with built-in pressure and temperature compensation gives you mass flow data in kg/h for saturated and superheated steam lines. Silver Automation Instruments supplies inline vortex meters from DN15 to DN300 with 4-20 mA HART output and ATEX Zone 1 certification. Send us your pressure in bar, temperature in °C, pipe size DN, and flow range in kg/h for a quote.
Plant engineers who audit steam systems need repeatable flow data over long runs. Orifice plates wear and clog. Turbine meters fail in wet steam. A vortex flow meter has no moving parts and handles high temperature steam without routine calibration. This makes it a practical choice for boiler distribution headers, branch lines, and process steam feeds.
In a steam energy audit you compare boiler fuel input against steam output. You also track steam loss through leaks, traps, and poor insulation. A vortex meter installed on each main steam line gives you kg/h values. This makes cost allocation simple. We have seen a food processing plant in Thailand cut its steam waste by 18 percent after installing vortex meters on three saturated steam headers.
Saturated steam has a fixed relationship between pressure and temperature. You can calculate density from pressure alone. Superheated steam needs both pressure and temperature signals because density depends on two variables. A vortex meter measures velocity and volumetric flow. For steam mass flow in kg/h, the meter or flow computer must correct for density.
Silver Instruments offers multivariable vortex flow meters with an integrated pressure sensor and a PT100 temperature probe. These units output mass flow directly over 4-20 mA HART. This setup removes the need for a separate flow computer. Most engineers skip this part during specification but it matters during commissioning.
For saturated steam up to 16 bar, a standard vortex meter with external pressure compensation works well. For superheated steam above 200 °C, we recommend the multivariable version. The density calculation updates every second inside the transmitter. This gives reliable readings even when boiler load changes.
Pick the right meter based on pipe size, pressure, temperature, and turndown. Silver Instruments vortex flow meters cover DN15 to DN300. Standard body material is 316L stainless steel. Temperature range goes up to 400 °C for superheated steam. Pressure rating is PN40 or ANSI Class 300 depending on flange.
Analog output is 4-20 mA HART. Pulse output is also available for totalization. Accuracy is ±1.5 percent of reading for steam above 15 m/s. Turndown ratio is 10:1 to 20:1 depending on line size. The electronics can be remote mounted to protect them from pipe heat. ATEX Zone 1 and IECEx approvals are available for gas and steam areas.
Steam viscosity stays near 0.02 cP at 200 °C. That is low. Reynolds numbers remain high. Vortex shedding stays linear across the flow range. For saturated steam lines with stable pressure, a simple vortex meter plus pressure transmitter works. For superheated steam lines, specify the full multivariable version. Include a PT100 sensor and an internal pressure cell. The meter calculates kg/h and totalized mass flow. You can read data over HART with a handheld communicator or send it to a PLC.
Here is the thing. Vortex flow meters need straight pipe upstream and downstream. Use 15D upstream and 5D downstream for most steam lines. Avoid placing the meter after a control valve that flashes steam. Install the meter on a horizontal line with the electronics above the pipe or to the side. Do not mount the transmitter below the pipe on steam service unless the temperature is below 120 °C.
Before startup, open the steam isolation valves slowly. Water hammer can damage the bluff body. Drain condensate from the line before flow begins. Set the meter parameters in the local display or via HART. Enter the pipe inner diameter, steam type, and units. If you use an external pressure transmitter, wire it to the vortex meter or PLC for density compensation.
We have seen a customer in Vietnam install a vortex meter too close to a pressure reducing station. The flow readings were unstable because of swirl and flashing. Moving the meter 20 pipe diameters downstream fixed the problem. This is a common field mistake.
Silver Automation Instruments supplies inline and insertion vortex flow meters for steam energy audits. Inline meters fit DN15 to DN300. Insertion meters cover DN200 to DN2000 for large steam headers. Most audit projects use inline meters because they are easier to verify and calibrate.
For a 2 inch saturated steam line at 10 bar, choose the Silver Instruments inline vortex meter with integrated pressure compensation. The meter will measure volumetric flow and calculate mass flow in kg/h. For a 6 inch superheated steam line at 28 bar and 320 °C, choose the multivariable vortex meter with PT100 and internal pressure sensor. Remote electronics are standard for this operating range.
Contact us with your steam conditions. Send us your pressure in bar, temperature in °C, pipe size DN, and flow range in kg/h. Our team will recommend a meter and provide a quote within one business day.
Tel: +86-25-68650347
Whatsapp: +86-25-52155837
WeChat: +86 15365082610
Can a vortex flow meter measure both saturated and superheated steam?
Yes. The same meter body works for both steam types. For saturated steam, pressure compensation is enough. For superheated steam, add temperature compensation with a PT100 probe.
What is the typical accuracy for steam mass flow?
Expect ±1.5 percent of reading for steam velocities above 15 m/s. Below that, accuracy drops. Size the meter so normal flow stays above 20 m/s.
Do I need a separate flow computer for steam mass flow?
Not with a multivariable vortex flow meter. The electronics calculate density and mass flow directly. Output is 4-20 mA HART for kg/h.
What straight pipe length is required?
15D upstream and 5D downstream is standard. Add more upstream length after elbows, valves, or pressure reducing stations.
What approvals are available for hazardous areas?
ATEX Zone 1 and IECEx certifications are available. Specify this when you send your steam conditions.
